Видео

How donyou make it more sensitive because mine is nit sensitive at all

What do I do if mine came with no yellow wires to tap into the lights ? It came with a 9v battery connection! Can I just solder the wires to the logic board? Looks like xh1 xh2 MD xh3??

Quick question.. with the 100 ohms resistor that was placed in between the ignition wires to emulate the same resistance in the ignition itself... you simply joined the 2 connections to get 100 ohms .5w resistance before the key.. the fact that the connection to the key is still connected.. doesn't that mess with the resistance once the key is turned ? (200 ohms 1w ??) it seems like you should cut off the factory resistance and rely solely on the resistor you put in.

Maybe you’ll see this, maybe not. But it seems like you made the shapes go over the three lines while drawing them. I’m a bit confused. Does it not have to be perfectly within the lines?

Thanks for the tutorial, it was most helpful. I have one complaint though; when I am done riding the bike and I put it in neutral and turn the engine off, the alarm makes 3 beeps, stops and after a short while it makes 3 beeps again. It only stops when I arm the alarm. Is there a way for me to stop this beeps when the alarm is not armed?

Great video and I did not wreck my bike - luckily! Tank repair for a 1976 Yamaha RD400 drag bike which came with dents - motor ready - thanks for the help!

Wow that's amazing

Bro did it the hardest way possible

Hi my name is kia im the silaturahim girl that aks you ❤(i subscribed you)

If you see how the do in in india is very easy

Thick and wet. Just how I like my women.

Anyone know the brand name of the circuit tester he's using please?

So all of a sudden you start saying u prime. ??????

wiring it to blow a fuse if someone hot wires it while the alarm is armed is genius

i got it thank u

Holy Crap, your volume on the closing audio is WAY too high.

2nd layer pls..

Try the same thing on my bike tank even use aluminum instead of plastic parts to glue on to the tank when the heat gun glue didn't work I even tried to use J-B weld and it didn't even work when I applied the glue as well as the JB weld it's still didn't hold and will not come out I will say I was pulling this dent on a old 1981 Kawasaki tank

What types of sand paper are used in this ??

Where can I get the tank pad material

Hello,.i'm from Belgium and I want also put this alarm on my motorcycle. I have got an Intruder VL1500LC suzuki intruder. Can you help me how and where I have to connect the wires? The red, Black and the 2 yellow, are no problems. But the rest i don't know.

Great video! Most suck. You did not. Great work. Keep it up!

Handy tip if you unplug the screamer while your fitting this, the alarm will still give off enough noise to notify you that it's triggering properly without deafening you. Once your done tinkering you can plug it back in and have your ears unharmed. Given how many bikes are sold with alarms that have been bodged into place this comes in handy if you have an alarm pre-installed but doesn't work as intended so you have to play around to find the short

@Brovacs Can you please give me some advice, my starter relay wire is blue and white but it connects to the starter switch too, I see you have a different wiring set up, can I email you my wiring diagram? Or Google can help..... It's a Yamah XJ6 F Diversion 2013 I've wired up the lights and power to the unit.

I've wired up exactly how you've explained but have a slight problem... When I "start" my bike with the fob all it does is turn on the electrical system... it doesn't actually start her up, I was thinking maybe it was to do with the clutch switch, but that doesn't make a difference if I hold the clutch in...

I don't know English, I understood everything, but I don't know anything with resistance. should it be connected to the cable between the alarm and the switch box???

I don't know English, I understood everything, but I don't know anything with resistance. should it be connected to the cable between the alarm and the switch box???

Thank you! You coached me through my first solve!

Seems to blow fuse, where do I put the resistor?

❤

❤

❤

This video was uploaded 6 years ago I don't think he's going to respond

Hard

Doing the alg is not that jard

Sorry, but the "whiiiit whit whiiiiit whit" music in the background while I'm trying to listen to you made this unwatchable for me. Thanks anyway.

Thank you

Will that alarm work for a yamaha r7 2024

Thank you so much, your tutorial is really helpful, I just need to do it again and again until I get it, thank you ✨💕💕

❤❤nice 🎉

Thanks for your time man, this has been enlightening.

Hi, What I'd bottom, 2nd and 3rd layers are done all that is missing is the edge pieces of red, blue, green, orange and yellow

letters are ok, but putting paint in rubber bands looks like shit.

Does Bondo stick well to a outside gas tank??...Another Question, will it Crack due to expansion?

Y

This helped me a lot thanks But the best part is the into banger song

Every time my alarm is triggered it blows a fuse .. great idea until a gust of wind gets under your cover 😮

Really helpful video But I have a question When you wire the Emobiliser I am not sure what you ment sorry I really not sure what to cut My bike is a royle Enfield intersepter 2018

Where did u get these double splice connectors? (Tap connector you named it)

Thank you and nice job man!